To Next Page

To Previous Page

Parameters

List of parameters

1-1004

SINAMICS S List Manual (LH1), 07/2007

Description: Sets the minus cam position for the function "Safe Cam" (SCA).

Index: [0] = Cam position SCA1 (SN1)

[1] = Cam position SCA2 (SN2)

[2] = Cam position SCA3 (SN3)

[3] = Cam position SCA4 (SN4)

[4] = Cam position SCA5 (SN5)

[5] = Cam position SCA6 (SN6)

[6] = Cam position SCA7 (SN7)

[7] = Cam position SCA8 (SN8)

[8] = Cam position SCA9 (SN9)

[9] = Cam position SCA10 (SN10)

[10] = Cam position SCA11 (SN11)

[11] = Cam position SCA12 (SN12)

[12] = Cam position SCA13 (SN13)

[13] = Cam position SCA14 (SN14)

[14] = Cam position SCA15 (SN15)

[15] = Cam position SCA16 (SN16)

[16] = Cam position SCA17 (SN17)

[17] = Cam position SCA18 (SN18)

[18] = Cam position SCA19 (SN19)

[19] = Cam position SCA20 (SN20)

[20] = Cam position SCA21 (SN21)

[21] = Cam position SCA22 (SN22)

[22] = Cam position SCA23 (SN23)

[23] = Cam position SCA24 (SN24)

[24] = Cam position SCA25 (SN25)

[25] = Cam position SCA26 (SN26)

[26] = Cam position SCA27 (SN27)

[27] = Cam position SCA28 (SN28)

[28] = Cam position SCA29 (SN29)

[29] = Cam position SCA30 (SN30)

Dependency: Refer to: p9501, p9503, p9536

Note: A change only becomes effective after a POWER ON.

SCA: Safe Cam / SN: Safe software cam

Description: Sets the minus cam position for the function "Safe Cam" (SCA).

Index: [0] = Cam position SCA1 (SN1)

[1] = Cam position SCA2 (SN2)

[2] = Cam position SCA3 (SN3)

[3] = Cam position SCA4 (SN4)

[4] = Cam position SCA5 (SN5)

[5] = Cam position SCA6 (SN6)

[6] = Cam position SCA7 (SN7)

p9537[0...29] SI motion SCA (SN) plus cam position (Control Unit) / SI Mtn SCA-

SERVO, VECTOR Can be changed: U, T Calculated: - Access level: 4

Data type: Floating Point Dynamic index: - Func. diagram: -

P-Group: Safety Integrated Units group: - Unit selection: -

Not for motor type: - Expert list: 1

Min Max Factory setting

-2147000.000 [mm] 2147000.000 [mm] -10.000 [mm]

p9537[0...29] SI motion SCA (SN) plus cam position (Control Unit) / SI Mtn SCA-

SERVO (Safety rot),

VECTOR (Safety rot)

Can be changed: U, T Calculated: - Access level: 4

Data type: Floating Point Dynamic index: - Func. diagram: -

P-Group: Safety Integrated Units group: - Unit selection: -

Not for motor type: - Expert list: 1

Min Max Factory setting

-2147000.000 [°] 2147000.000 [°] -10.000 [°]

Brand	Siemens
Model	SINAMICS S Series
Category	Industrial Equipment
Language	English

Siemens SINAMICS S Series User Manual

Table of Contents

Questions and Answers:

Siemens SINAMICS S Series Specifications

Related product manuals