Siemens SINAMICS S Series - p2628 BI: EPOS traversing block selection, bit 3; Trav_blk sel bit 3; p2629 BI: EPOS traversing block selection, bit 4; Trav_blk sel bit 4; p2630 BI: EPOS traversing block selection, bit 5; Trav_blk sel bit 5; p2631 BI: EPOS activate traversing task (0 -> 1); Trav_task act

Parameters
List of parameters
1-660
© Siemens AG 2007 All Rights Reserved
SINAMICS S List Manual (LH1), 07/2007
Description: Sets the signal source to select the traversing block, bit 3.
Dependency: Binector inputs p2625, p2626, p2627, p2628, p2629 and p2630 are used to select one of the maximum of 64 tra-
versing blocks.
Refer to: p2625, p2626, p2627, p2629, p2630
Description: Sets the signal source to select the traversing block, bit 4.
Dependency: Binector inputs p2625, p2626, p2627, p2628, p2629 and p2630 are used to select one of the maximum of 64 tra-
versing blocks.
Refer to: p2625, p2626, p2627, p2628, p2630
Description: Sets the signal source to select the traversing block, bit 5.
Dependency: Binector inputs p2625, p2626, p2627, p2628, p2629 and p2630 are used to select one of the maximum of 64 tra-
versing blocks.
Refer to: p2625, p2626, p2627, p2628, p2629
Description: Sets the signal source for "activating traversing task".
BI: p2631 = 0/1 signal
The traversing task, selected using BI: p2625 ... p2630, is started.
Dependency: Refer to: p2625, p2626, p2627, p2628, p2629, p2630, p2640, p2641
Notice: The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
p2628 BI: EPOS traversing block selection, bit 3 / Trav_blk sel bit 3
SERVO (EPOS),
VECTOR (EPOS)
Can be changed: T Calculated: - Access level: 1
Data type: Unsigned32 / Binary Dynamic index: - Func. diagram: 3640
P-Group: Basic positioner Units group: - Unit selection: -
Not for motor type: - Expert list: 1
Min Max Factory setting
- - 0
p2629 BI: EPOS traversing block selection, bit 4 / Trav_blk sel bit 4
SERVO (EPOS),
VECTOR (EPOS)
Can be changed: T Calculated: - Access level: 1
Data type: Unsigned32 / Binary Dynamic index: - Func. diagram: 3640
P-Group: Basic positioner Units group: - Unit selection: -
Not for motor type: - Expert list: 1
Min Max Factory setting
- - 0
p2630 BI: EPOS traversing block selection, bit 5 / Trav_blk sel bit 5
SERVO (EPOS),
VECTOR (EPOS)
Can be changed: T Calculated: - Access level: 1
Data type: Unsigned32 / Binary Dynamic index: - Func. diagram: 3640
P-Group: Basic positioner Units group: - Unit selection: -
Not for motor type: - Expert list: 1
Min Max Factory setting
- - 0
p2631 BI: EPOS activate traversing task (0 -> 1) / Trav_task act
SERVO (EPOS),
VECTOR (EPOS)
Can be changed: T Calculated: - Access level: 1
Data type: Unsigned32 / Binary Dynamic index: - Func. diagram: 3640
P-Group: Basic positioner Units group: - Unit selection: -
Not for motor type: - Expert list: 1
Min Max Factory setting
- - 0