Siemens SINAMICS S Series - 1.3.3 Parameters for Encoder Data Sets (EDS)

Parameters
Parameters for data sets
1-1082
© Siemens AG 2007 All Rights Reserved
SINAMICS S List Manual (LH1), 07/2007
p3827[0...n] Friction characteristic, value v7 / Friction v7
p3828[0...n] Friction characteristic, value n8 / Friction n8
p3828[0...n] Friction characteristic, value v8 / Friction v8
p3829[0...n] Friction characteristic, value n9 / Friction n9
p3829[0...n] Friction characteristic, value v9 / Friction v9
p3830[0...n] Friction characteristic, value M0 / Friction M0
p3830[0...n] Friction characteristic, value F0 / Friction F0
p3831[0...n] Friction characteristic, value M1 / Friction M1
p3831[0...n] Friction characteristic, value F1 / Friction F1
p3832[0...n] Friction characteristic, value M2 / Friction M2
p3832[0...n] Friction characteristic, value F2 / Friction F2
p3833[0...n] Friction characteristic, value M3 / Friction M3
p3833[0...n] Friction characteristic, value F3 / Friction F3
p3834[0...n] Friction characteristic, value M4 / Friction M4
p3834[0...n] Friction characteristic, value F4 / Friction F4
p3835[0...n] Friction characteristic, value M5 / Friction M5
p3835[0...n] Friction characteristic, value F5 / Friction F5
p3836[0...n] Friction characteristic, value M6 / Friction M6
p3836[0...n] Friction characteristic, value F6 / Friction F6
p3837[0...n] Friction characteristic, value M7 / Friction M7
p3837[0...n] Friction characteristic, value F7 / Friction F7
p3838[0...n] Friction characteristic, value M8 / Friction M8
p3838[0...n] Friction characteristic, value F8 / Friction F8
p3839[0...n] Friction characteristic, value M9 / Friction M9
p3839[0...n] Friction characteristic, value F9 / Friction F9
p3846[0...n] Friction characteristic record ramp-up/ramp-down time / Frict rec t_RFG
p3847[0...n] Friction characteristic record warm-up time / Frict rec t_warm
r3925[0...n] Identification final display / Ident final_disp
r3927[0...n] Motor data identification determined data (induction motor) / MotID det dat ASM
r3928[0...n] Motor data identification determined data (synchronous motor) / MotId determ SM
p7035[0...n] Par_circuit circulating current control operating mode / Circ_I mode
p7036[0...n] Par_circuit circulating current control proportional gain / Circ_I Kp
p7037[0...n] Par_circuit circulating current control integral time / I_circ Tn
p7038[0...n] Par_circuit circulating current control limit / I_circ limit
1.3.3 Parameters for Encoder Data Sets (EDS)
The following list contains the encoder-data-set-dependent parameters.
Product: SINAMICS S, Version: 2503100, Language: eng
p0141[0...n] Encoder interface (Sensor Module) component number / Enc_interf comp_no
p0142[0...n] Encoder component number / Encoder comp_no
p0144[0...n] Sensor Module detection via LED / SM detection LED
p0145[0...n] Activate/de-activate encoder interface / Enc_intf act/deact
r0146[0...n] Encoder interface active/inactive / Enc_intf act/inact
r0147[0...n] Sensor Module EPROM data version / SM EEPROM version
Note:
References: /FH1/ SINAMICS S120 Function Manual Drive Functions
Section "Data sets"