Siemens SINAMICS S Series - 1.3 Parameters for data sets; 1.3.1 Parameters for Command Data Sets (CDS)

Parameters for data sets
Parameters
1-1069
© Siemens AG 2007 All Rights Reserved
SINAMICS S List Manual (LH1), 07/2007
1.3 Parameters for data sets
1.3.1 Parameters for Command Data Sets (CDS)
The following list contains the command-data-set-dependent parameters.
Product: SINAMICS S, Version: 2503100, Language: eng
p0700[0...n] Macro Binector Input (BI) / Macro BI
p0820[0...n] BI: Drive data set selection DDS bit 0 / DDS select., bit 0
p0821[0...n] BI: Drive data set selection DDS bit 1 / DDS select., bit 1
p0822[0...n] BI: Drive data set selection DDS bit 2 / DDS select., bit 2
p0823[0...n] BI: Drive data set selection DDS bit 3 / DDS select., bit 3
p0824[0...n] BI: Drive data set selection DDS bit 4 / DDS select., bit 4
p0828[0...n] BI: Motor changeover, feedback signal / Mot_chng fdbk sig
p0840[0...n] BI: ON/OFF1 / ON/OFF1
p0844[0...n] BI: 1. OFF2 / 1. OFF2
p0845[0...n] BI: 2. OFF2 / 2. OFF2
p0848[0...n] BI: 1. OFF3 / 1. OFF3
p0849[0...n] BI: 2. OFF3 / 2. OFF3
p0852[0...n] BI: Enable operation / Enable operation
p0854[0...n] BI: Master ctrl by PLC / Master ctrl by PLC
p0855[0...n] BI: Unconditionally release holding brake / Uncond open brake
p0856[0...n] BI: Enable speed controller / Enable n_ctrl
p0856[0...n] BI: Enable velocity controller / Enable v_ctrl
p0858[0...n] BI: Unconditionally close holding brake / Uncond close brake
p1000[0...n] Macro Connector Inputs (CI) for speed setpoints / Macro CI n_set
p1000[0...n] Macro Connector Inputs (CI) for velocity setpoints / Macro CI v_set
p1020[0...n] BI: Fixed speed setpoint selection Bit 0 / n_set_fixed Bit 0
p1020[0...n] BI: Fixed velocity setpoint selection Bit 0 / v_set_fixed Bit 0
p1021[0...n] BI: Fixed speed setpoint selection Bit 1 / n_set_fixed Bit 1
p1021[0...n] BI: Fixed velocity setpoint selection Bit 1 / v_set_fixed Bit 1
p1022[0...n] BI: Fixed speed setpoint selection Bit 2 / n_set_fixed Bit 2
p1022[0...n] BI: Fixed velocity setpoint selection Bit 2 / v_set_fixed Bit 2
p1023[0...n] BI: Fixed speed setpoint selection Bit 3 / n_set_fixed Bit 3
p1023[0...n] BI: Fixed velocity setpoint selection Bit 3 / v_set_fixed Bit 3
p1035[0...n] BI: Motorized potentiometer setpoint raise / Mop raise
p1036[0...n] BI: Motorized potentiometer lower setpoint / Mop lower
p1039[0...n] BI: Motorized potentiometer inversion / Mop inversion
p1041[0...n] BI: Motorized potentiometer manual/automatic / Mop manual/auto
p1042[0...n] CI: Motorized potentiometer automatic setpoint / Mop auto setpoint
p1043[0...n] BI: Motorized potentiometer accept setpoint / Mop accept set val
p1044[0...n] CI: Motorized potentiometer setting value / Mop setting value
p1055[0...n] BI: Jog bit 0 / Jog bit 0
p1056[0...n] BI: Jog bit 1 / Jog bit 1
p1070[0...n] CI: Main setpoint / Main setpoint
Note:
References: /FH1/ SINAMICS S120 Function Manual Drive Functions
Section "Data sets"