Siemens SINAMICS S Series - Page 1070

Parameters
Parameters for data sets
1-1070
© Siemens AG 2007 All Rights Reserved
SINAMICS S List Manual (LH1), 07/2007
p1071[0...n] CI: Main setpoint scaling / Main setp scal
p1075[0...n] CI: Suppl setpoint / Suppl setpoint
p1076[0...n] CI: Supplementary setpoint scaling / Suppl setp scal
p1085[0...n] CI: Speed limit in positive direction of rotation / n_limit pos
p1085[0...n] CI: Velocity limit positive direction / v_limit pos
p1088[0...n] CI: Speed limit negative direction of rotation / n_limit neg
p1088[0...n] CI: Velocity limit negative direction / n_limit neg
p1110[0...n] BI: Inhibit negative direction / Inhib neg dir rot
p1111[0...n] BI: Inhibit positive direction / Inhib pos dir rot
p1113[0...n] BI: Direction reversal / Direction reversal
p1122[0...n] BI: Bypass ramp-function generator / Bypass RFG
p1140[0...n] BI: Enables the ramp-function generator / Enable RFG
p1141[0...n] BI: Start ramp-function generator / Start RFG
p1142[0...n] BI: Enable speed setpoint / Enable n_set
p1142[0...n] BI: Enable velocity setpoint / Enable v_set
p1143[0...n] BI: Ramp-function generator, accept setting value / Accept RFG set val
p1144[0...n] CI: Ramp-function generator setting value / RFG setting value
p1155[0...n] CI: Speed controller speed setpoint 1 / n_ctrl n_set 1
p1155[0...n] CI: Velocity controller, velocity setpoint 1 / v_ctrl n_set 1
p1160[0...n] CI: Speed controller speed setpoint 2 / n_ctrl n_set 2
p1160[0...n] CI: Velocity controller, velocity setpoint 2 / v_ctrl n_set 2
p1230[0...n] BI: Armature short-circuit / DC brake activation / ASC act
p1235[0...n] BI: External armature short-circuit, contactor feedback signal / ASC ext feedback
p1330[0...n] CI: V/Hz control independent voltage setpoint / Vf V_set independ.
p1356[0...n] CI: V/f control, angular setpoint / Uf ang setpoint
p1430[0...n] CI: Speed pre-control / n_prectrl
p1430[0...n] CI: Velocity pre-control / v_prectrl
p1437[0...n] CI: Speed controller, reference model I component input / n_ctrRefMod I_comp
p1455[0...n] CI: Speed controller P gain adaptation signal / n_ctrl Adpt_sig Kp
p1455[0...n] CI: Velocity controller, P gain adaptation signal / v_ctrl Adpt_sig Kp
p1466[0...n] CI: Speed controller P-gain scaling / n_ctrl Kp scal
p1466[0...n] CI: Velocity controller P gain scaling / v_ctrl Kp scal
p1476[0...n] BI: Speed controller hold integrator / n_ctrl integ stop
p1476[0...n] BI: Velocity controller, hold integrator / v_ctrl integ stop
p1477[0...n] BI: Speed controller set integrator value / n_ctrl integ set
p1477[0...n] BI: Set velocity controller integrator value / v_ctrl integ set
p1478[0...n] CI: Speed controller integrator setting value / n_ctr integ_setVal
p1478[0...n] CI: Velocity controller, integrator value / v_ctr integ_setVal
p1479[0...n] CI: Speed controller integrator setting value scaling / n_ctrl I_val scal
p1492[0...n] BI: Droop feedback enable / Enables droop
p1495[0...n] CI: Acceleration pre-control / a_prectrl
p1497[0...n] CI: Moment of inertia, scaling / M_mom inert scal
p1497[0...n] CI: Motor weight scaling / Mot_weight scal
p1500[0...n] Macro Connector Inputs (CI) for torque setpoints / Macro CI M_set
p1500[0...n] Macro Connector Inputs (CI) for force setpoints / Macro CI F_set
p1501[0...n] BI: Change over between closed-loop speed/torque control / Changeov n/M_ctrl
p1501[0...n] BI: Changeover velocity/force control / Changeov n/F_ctrl
p1503[0...n] CI: Torque setpoint / M_set
p1511[0...n] CI: Supplementary torque 1 / M_suppl 1
p1511[0...n] CI: Supplementary force 1 / F_suppl 1
p1512[0...n] CI: Supplementary torque 1 scaling / M_suppl 1 scal
p1512[0...n] CI: Supplementary force 1 scaling / F_suppl 1 scal
p1513[0...n] CI: Supplementary torque 2 / M_suppl 2