Function Diagrams
Faults and alarms
2-1334
© Siemens AG 2007 All Rights Reserved
SINAMICS S List Manual (LH1), 07/2007
Figure 2-211 8060 – Fault buffer
- 8060 -
Function diagram
87654321
fp_8060_51_eng.vsd
DO: All objects
SINAMICS
10.11.06 V02.05.00
Faults and alarms - Fault buffer
<1>
Actual
fault case
Fault 1
Fault 2
Fault 8
RESET
Fault case comes
Fault case count
p0952
p0952 = 0:
Fault buffer is deleted/cleared
Delete fault buffer
r0945 = 0
r0948 = 0
r0949 = 0
r2109 = 0
r2130 = 0
r2133 = 0
r2136 = 0
Automatic
7. Acknow-
ledged
fault case
[oldest]
1. Acknow-
ledged
fault case
Fault goes
Fault comes
Fault buffer
change
r0944
Fault buffer change [8065.6]
Counter
16 bit
LED "RDY" [= red for fault]
r2131
Actual fault code
0 = "No fault present"
III
RESET
III
RESET
III
32 bit counter,
free running
1 ms
System time
r0969 [ms]
16 bit counter,
free running
POWER ON
Fault responses to the sequence control [2610]
<1> This fault is overwritten when "more recent" faults occur (with the exception of "safety faults").
[8065.1]
Operating time
Acknowledging faults
r2138.7
External fault 1
r2138.13
External fault 2
r2138.14
External fault 3
r2138.15
1
Fault case acknowl.
Background
Refer to [1020.7]
[2546.7]
p2102 ... p2105
[2546.7]
p2106
[2546.7]
p2107
[2546.7]
p2108, p3110 ... p3112
Fault active
r2139.3 [2548.2]
Acknowledge faults
p3981
Fault code
Fault 1
Fault 2
Fault 8
r0949[63] [I32]
r2133[63] [Float]
Fault 1
Fault 2
Fault 8
r0945[0]
r0945[1]
r0945[7]
r0945[56]
r0945[57]
r0945[63]
r0945[8]
r0945[9]
r0945[15]
Fault value
r0949[0] [I32]
r2133[0] [Float]
r0949[1] [I32]
r2133[1] [Float]
r0949[7] [I32]
r2133[7] [Float]
r0949[56] [I32]
r2133[56] [Float]
r0949[57] [I32]
r2133[57] [Float]
r0949[8] [I32]
r2133[8] [Float]
r0949[9] [I32]
r2133[9] [Float]
r0949[15] [I32]
r2133[15] [Float]
Fault time
"come"
r0948[0] [ms]
r2130[0] [d]
r0948[1] [ms]
r2130[1] [d]
r0948[7] [ms]
r2130[7] [d]
r0948[56] [ms]
r2130[56] [d]
r0948[57] [ms]
r2130[57] [d]
r0948[63] [ms]
r2130[63] [d]
r0948[8] [ms]
r2130[8] [d]
r0948[9] [ms]
r2130[9] [d]
r0948[15] [ms]
r2130[15] [d]
Fault time
"removed"
r2109[0] [ms]
r2136[0] [d]
r2109[1] [ms]
r2136[1] [d]
r2109[7] [ms]
r2136[7] [d]
r2109[56] [ms]
r2136[56] [d]
r2109[57] [ms]
r2136[57] [d]
r2109[63] [ms]
r2136[63] [d]
r2109[8] [ms]
r2136[8] [d]
r2109[9] [ms]
r2136[9] [d]
r2109[15] [ms]
r2136[15] [d]
1
p2147 (CU) = 1
<2> Refer to the list manual, index entry "Fault buffer - save upon power OFF".
<2>
POWER ON
Fault times
Faults
Acknowledging
<3> The buffer parameters are cyclically updated in the background (refer to the status signal in r2139).
<3>
Control Unit
Fault Present
r3114.10
To Next Page
Loading...
