List of parameters
Parameters
1-493
© Siemens AG 2007 All Rights Reserved
SINAMICS S List Manual (LH1), 07/2007
Dependency: In the simulation mode, the parameter cannot be written into. When selecting the motor data identification routine,
the drive data set changeover is suppressed.
Refer to: p1272, p1300, p1910, p1960, p1990
Refer to: A07980, A07981, F07982, F07983, F07984, F07985, F07986, A07987, F07988, F07990, A07991
Notice: In order to permanently accept the determined settings they must be saved in a non-volatile fashion (p0971,
p0977).
Note: An appropriate alarm is output when the parameter is set.
The power-on command must remain set during a measurement and after the measurement has been completed,
the drive automatically resets it.
The duration of the measurements can lie between 0.3 s and several minutes. This time is, for example, influenced
by the motor size and the mechanical conditions.
p1900 is automatically set to 0 after the motor data identification routine has been completed.
Description: Sets the configuration of the motor data identification.
Recommend.: For the stationary motor data identification, if a motor holding brake is being used it should be opened and the
motor finely synchronized before the measurement. This should only be done if it can be safely carried out and no
external forces can act on the motor. This determine the angular commutation offset (p1909.13, p0431).
Dependency: Refer to: p1910, r1912, r1913, r1915, r1925, r1927, r1932, r1933, r1934, r1935, r1936, r1950, r1951, p1952, p1953
Note: For an induction motor (ASM), the following bits are effective: 8, 9, 10, 13
For a synchronous motor (SRM), the following bits are effective: 8, 9, 13, 14
Re bit 14:
- after successfully determining the voltage emulation error, the display of the phase voltage actual values r0089
and the active power actual value r0082 and the torque actual value r0080 are significantly more accurate.
- the voltage emulation errors should be identified with the Motor Module in the warm state.
- the motor temperature (r0035) should not change significantly (i.e. it should not be identified immediately after a
load duty cycle).
Description: Sets the configuration of the motor data identification.
Recommend.: For the stationary motor data identification, if a motor holding brake is being used it should be opened and the
motor finely synchronized before the measurement. This should only be done if it can be safely carried out and no
external forces can act on the motor. This determine the angular commutation offset (p1909.13, p0431).
p1909[0...n] Motor data identification control word / MotID STW
SERVO Can be changed: T Calculated: CALC_MOD_ALL Access level: 3
Data type: Unsigned16 Dynamic index: MDS, p0130 Func. diagram: -
P-Group: Motor identification Units group: - Unit selection: -
Not for motor type: - Expert list: 1
Min Max Factory setting
- - 0010 0111 0000 0000 bin
Bit field: Bit Signal name 1 signal 0 signal FP
08 Measure D inductance Yes No -
09 Measure Q inductance Yes No -
10 Magnetizing field inductance and measure
rotor resistance
Yes No -
13 Measure commutation angle and direction
of rotation
Yes No -
14 Determining the voltage emulation error Yes No -
p1909[0...n] Motor data identification control word / MotID STW
SERVO (Exp M_ctrl) Can be changed: T Calculated: CALC_MOD_ALL Access level: 3
Data type: Unsigned16 Dynamic index: MDS, p0130 Func. diagram: -
P-Group: Motor identification Units group: - Unit selection: -
Not for motor type: - Expert list: 1
Min Max Factory setting
- - 0110 0111 0000 0000 bin
To Next Page
Loading...
